Welcome to the Linux Foundation Forum!

New training version with calico does not work [LAB 3.3]

miro 19
miro 19 Posts: 3
edited August 2018 in LFS258 Class Forum

In Lab 3.3 at step 20 there is no response from curl method (after some time it returns timeout). It worked with flannel. With calico it seems to block connection to the both Cluster IP and Enpoint IP. In addition ping from master node to worker node works but there is timeout trying to ping Cluster IP or Endpoint IP from master node (with flannel it worked).  All steps before were done according to the lab instruction.

Any idea what could be wrong?

Comments

  • serewicz
    serewicz Posts: 947

    Hello,

    Thank you for the feedback. Would it be possible to paste the last few commands, and their output? As you mentioned it hangs, but perhaps something in that and the previous output will help debug the problem.

    Regards,

  • serewicz
    serewicz Posts: 947

    Hello again,

    In case you didn't see it, step 20 does have this entry: 


    ...If the curl command times out the pod may be running on the other node. 
Run the same command on that node and it should work.

    Regards,

     

  • miro 19
    miro 19 Posts: 3
    edited August 2018

    Thanks for reply. I have checked curl on the same node as nginx pod is running and then it works. I thought it should work also from another pods (it worked that way whith flannel) especially when trying to use ClusterIP. I suppose this is correct behavior. Is it related with calico network policy? I am asking because I am curious why it is different from flannel.

    From node1:


    [email protected]:~$ kubectl get svc,ep
NAME                 TYPE        CLUSTER-IP    EXTERNAL-IP   PORT(S)   AGE
service/kubernetes   ClusterIP   10.96.0.1     <none>        443/TCP   8h
service/nginx        ClusterIP   10.96.12.64   <none>        80/TCP    8h

NAME                   ENDPOINTS            AGE
endpoints/kubernetes   10.142.0.2:6443      8h
endpoints/nginx        192.168.169.131:80   8h


[email protected]:~$ curl 10.96.12.64:80
curl: (7) Failed to connect to 10.96.12.64 port 80: Connection timed out

    From node2:


    [email protected]:~$ curl 192.168.169.131:80
<!DOCTYPE html>
<html>
<head>
<title>Welcome to nginx!</title>
<style>
    body {
        width: 35em;
        margin: 0 auto;
        font-family: Tahoma, Verdana, Arial, sans-serif;
    }
</style>
</head>
<body>
<h1>Welcome to nginx!</h1>
<p>If you see this page, the nginx web server is successfully installed and
working. Further configuration is required.</p>

<p>For online documentation and support please refer to
<a href="http://nginx.org/">nginx.org</a>.<br/>
Commercial support is available at
<a href="http://nginx.com/">nginx.com</a>.</p>

<p><em>Thank you for using nginx.</em></p>
</body>
</html>

     

  • serewicz
    serewicz Posts: 947

    One way to narrow down the problem is to run wireshark or tcpdump on the interfaces in use. If the curl request leaves the master node, but does not show up on the worker node you would know that something in the middle is blocking the traffic. If the traffic is arriving on the worker node this would indicate an issue with the service or perhaps kube-proxy on the target node. 

    As Fabio mentioned if you are using GCE you need to ensure that no traffic is being blocked. Other tools like VirtualBox and AWS have a slightly different manner to ensure all traffic is allowed.

  • miro 19
    miro 19 Posts: 3

    Indeed the problem was with GCE firewall. I saw that the traffic comes out of the node1 but does not arrive to node2. In fact ping and HTTP ports were open so it worked for some scenarios but it does not work for others, eg. complete demo example from lab 4.3 was working partially as there were no images on the page until traffic was open on firewall settings in GCE.

    Thanks for helping with this issue.

  • Armox176
    Armox176 Posts: 5

    Hi,

    I had the same problem (yes I think it IS a problem) and I solved it allowing ALL the traffic between the cluster nodes. If you are in GCE like me:

    1. Tag all the hosts of the cluster with the same network tag, say "k8s".
    2. Add a firewall rule to allow all the traffic from hosts tagged "k8s" to hosts tagged "k8s".

    Let me know if you need more details on it.

    Fabio

  • jitapichab
    jitapichab Posts: 1

    Thanks, I solved it allowing All traffic too , I want to know, why this action is necessary ?. before to this action I have allowed All TCP traffic but this didn't work !

    Jorge.

  • chrispokorni
    chrispokorni Posts: 1,169

    Hi @jitapichab,

    Kubernetes is an API driven architecture, and all internal communication takes place via API calls. This implies that each agent will expose a port where it expects requests from other agents.

    A firewall rule to allow only TCP traffic will do just that - allow only the TCP traffic. Agents may use other protocols, so you would need to allow all protocols through, not only TCP.

    This can be achieved in multiple ways. Tagging instances and setting up firewall rules based on tags is one way. Creating an isolated VPC network, dedicated to you Kubernetes nodes, with a firewall rule to allow all traffic - all protocols, to all ports, from all sources, is another way.

    Regards.
    -Chris

Categories

Upcoming Training